PSD stalling when warm - PowerStrokeNation : Ford Powerstroke Diesel Forum
 
LinkBack Thread Tools Display Modes
post #1 of 7 (permalink) Old 06-01-2009, 08:16 PM Thread Starter
 
Join Date: May 2009
Posts: 3
PSD stalling when warm

Hey I have a 97 Ford f350, 7.3l,a/t, and 221k on the truck. The truck takes a bit to get started then will die when the motor warms up. and will not refire till motor cools down. The truck will also die on decceleration when the motor gets warm. I have searched and have done the following

* Swaped IDM
* Replaced CPS
* Replaced injector o-rings
* Replaced IPR o-rings
* New Glow plugs
* One of the glow plug harness' had a bad wire so i swaped that too
* Oil/Filter
* fuel filter


Where should I go from here?
Grama is offline  
Sponsored Links
Advertisement
 
post #2 of 7 (permalink) Old 06-02-2009, 01:56 AM
PSN Local
 
pjwoolw's Avatar
 
Join Date: Jan 2009
Location: San Ramon Ca.
Posts: 262
Re: PSD stalling when warm

Welcome to PSN. I would check fuel pressure first. Have you cleaned the FPR screen in the fuel filter / water separator?

Pete in San Ramon
2005 F250 6.0 Lariat 4x4 CC Short bed (stock)
1997 F250 7.3 XLT 4X4 Reg. cab (stock)
1986 F250 6.9 XLT Gone but not forgotten

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
pjwoolw is offline  
post #3 of 7 (permalink) Old 06-02-2009, 05:29 AM Thread Starter
 
Join Date: May 2009
Posts: 3
Re: PSD stalling when warm

Thanks Pjwoolw!

I clean the screen but havnt drained the water separator. Where is the water separator located?
Grama is offline  
 
post #4 of 7 (permalink) Old 06-02-2009, 11:06 PM
PSN Veteran
 
ADubDiesel's Avatar
 
Join Date: Feb 2008
Location: Bellevue, WA
Posts: 1,112
Re: PSD stalling when warm

It's a little lever on the back of the fuel filter housing. IIRC it's yellow in color.

1995 Ford F-250 7.3 (Sold)
1998 Nissan Maxima 3.0
ADubDiesel is offline  
post #5 of 7 (permalink) Old 06-03-2009, 04:31 AM
OEM Moderator
 
Tom S's Avatar
 
Join Date: Jul 2007
Location: Littleton, Colo
Posts: 9,381
Send a message via AIM to Tom S
Re: PSD stalling when warm

It sounds to me like you do not have enough HP oil when the oil is thin and warm. I would be monitoring that for some diagnosis.

Tom
Tom S is offline  
post #6 of 7 (permalink) Old 06-03-2009, 11:45 PM Thread Starter
 
Join Date: May 2009
Posts: 3
Re: PSD stalling when warm

where can a monitor the hp oil at?
Grama is offline  
post #7 of 7 (permalink) Old 06-04-2009, 12:03 AM
Starting Over
 
kainers's Avatar
 
Join Date: Jul 2007
Location: Klamath Falls, Oregon
Posts: 4,629
Re: PSD stalling when warm

Did you rebuild the IPR or just replace the orings?

Not that he doesn't have enough to do but CSIPSD lives in bend Pm him he has AE and can do a scan on your truck monitor you HPO psi.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
kainers is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the PowerStrokeNation : Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome