gauges - PowerStrokeNation : Ford Powerstroke Diesel Forum
 
LinkBack Thread Tools Display Modes
post #1 of 6 (permalink) Old 04-19-2008, 10:50 PM Thread Starter
PSN Local
 
Join Date: Jan 2008
Location: houston MO
Posts: 173
gauges

i bought me some gauges a boost a trans and a pryo i was wondering were the best place is to put the boost and how wer does the trans go and how do you hook it up its my first time with the trans dont mean to sound stupidif anyone can help me i would appreiate it thanks

1999 ford super duty ex cab short bed 4x4 dp-tuner f-5 lomp mod,80 econ,100,120 race,140 aggresive 4inch exaust to 6-inch tip non-wastegated housing upgrade from bts di-performance crossover line di-performance fuel tank mixing delete autometer gauges boost,trans,pyro custom made cold air intake.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
big bad stroker is offline  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old 04-19-2008, 10:55 PM
2nd class citizen
 
1snotrocket's Avatar
 
Join Date: Dec 2007
Location: vacaville,ca.
Posts: 797
Re: gauges

put the pyro in the driver side exhaust manifold near the flange.boost gauge i ran a vacum tee at the map sensor.you can install your trans temp gauge sender at the check port in left side of trans by the shift indicator you'll see a brass plug.

2003 CRW CAB LB 4X4 6SPD,AFE STAGE 2,38r,DP TUNER,4'' MBRP,FASS 15,Farmers Disel Performance 160/100 injectors,ITPREG.RETURN,TERMINATOR
2001 crw cab short bed auto 4x4 5"exhaust afe stg 2,f6,jw trans,terminator,cass. stg2's,itp reg return,fuel lab pump.
1snotrocket is offline  
post #3 of 6 (permalink) Old 04-19-2008, 11:13 PM
RDRCM
 
CooterBrown's Avatar
 
Join Date: Jul 2007
Location: Heath, TX
Posts: 1,922
Re: gauges

Could someone call Joe and let him know there is a gauge thread that he has not posted in. He won't answer when I call?

#49

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Sold

2006 Almighty CumminGs
CooterBrown is offline  
 
post #4 of 6 (permalink) Old 04-19-2008, 11:27 PM
Banned
 
Join Date: Oct 2007
Location: Redmond, OR
Posts: 2,283
Send a message via Yahoo to blk99
Re: gauges

Quote:
Originally Posted by big bad stroker View Post
i bought me some gauges a boost a trans and a pryo i was wondering were the best place is to put the boost and how wer does the trans go and how do you hook it up its my first time with the trans dont mean to sound stupidif anyone can help me i would appreiate it thanks
are you asking what order is best to put them in the pod or where they are all hooked up at??
blk99 is offline  
post #5 of 6 (permalink) Old 04-21-2008, 03:45 PM
Village Idiot
 
southmike's Avatar
 
Join Date: Jul 2007
Posts: 8,209
Re: gauges

actually joe had a good pic of that trans port somewhere ..
and most people do have an order preferance top to bottom.
if they are installed on the pillar...ie you want the egt to be the easiest to see.

Early 99 f350 4x4 crew cab, auto. pmt2 pcm
2001 cup holder ,T500, MAX AC ASSIST AC mod, Diy Twin tymar, TS chip, Powerslots & Hawk pads, ford AIC, ..... with big fat want to list.
southmike is offline  
post #6 of 6 (permalink) Old 04-21-2008, 05:25 PM
<<< THE GAUGE WHORE...
 
CSIPSD's Avatar
 
Join Date: Jul 2007
Location: Bend, OR
Posts: 12,083
Re: gauges

Here is a few shots... You can make up a Brass T for the boost and put it in your Map line, or you can drill and tap the Y pipe. You can also use the Intake Air Heater port for boost as well... Light blue in the second pic...

Pyro, In the manifold, Drill, tap and install. No need to vac, no need to grease the bit. Drill, Tap and install. Third Pic is the drill and tap, fourth is drill and clamp...

Tranny, In the test port on the drivers side, just above and infront of the shift linkage.
Attached Images
File Type: jpg map line.JPG (64.1 KB, 18 views)
File Type: jpg Top of motor shot.JPG (82.3 KB, 18 views)
File Type: jpg drivers side drill and tap.JPG (75.3 KB, 11 views)
File Type: jpg Drill and clamp on UP PIPE.JPG (65.7 KB, 12 views)
File Type: jpg trans temp port.JPG (69.7 KB, 14 views)

[CENTER]01 F-250 SC PSD,430k,16 Isspro Gauges, AFE-2,CCV Mod,IAH delete,map reg,Modded H2e, 6.0 IC, 230/100, Studs, 910 springs, Forged rods, Hydra chip, Swamps HVHF IDM, MBRP 4" dual's, Aero, 6" tip's, 4" Revtek lift, 37/12.5/16.5 MT's
Joe
CSIPSD is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the PowerStrokeNation : Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome